Skip to main content

Belajar Dasar SCADA

Post a Comment

OPERATOR ACCOUNT SCREENS AND OPTIONS


5.0        OPERATOR ACCOUNT SCREENS AND OPTIONS


7.1       After successfully logging onto the tester under the “operator” account, a window similar




7.2              The special function keys shown in Figure 4 are mapped to the F1 through F8 keys on the

keyboard.  These commands can be executed by pressing the appropriate “Fx” key or clicking on the box with the mouse.   (This works only when the mouse cursor is inside the window the contains the the special function keys.)


7.3              Lock the test fixture onto the testhead using the “fixture lock” command, F2 softkey.


7.4              Execute the “run testplan” command, F1 softkey.  This action will cause the tester to read the autofile code hard-strapped into the ICT test fixture.  The tester will then attempt to locate and load the testplan that corresponds to this autofile value.


NOTE:           If for some reason the tester is unable to locate the correct autofile that matches the ICT test fixture, a message will be displayed on the screen.  The message will state: Unable to locate autofile “XXXX”.   In this case

these boards can not be run from the operator account.  Notify test engineering of the problem.

7.5              If the load is successful then an HP3070 testmain will be displayed on the screen.  In addition the HP Board Graphics Viewer may be displayed as well.

 

7.6              Execute board testing as per paragraph 5.6 of the HP3070 Operating Procedure ,

SOP-3-1031-9.


7.7              When all testing is completed for this board type, execute the “exit” command, F8 softkey on the testmain window.  This will return you to the window shown in Figure 4.


7.8              Execute the “test fixture unlock” command, F3 softkey.


7.9              If there is another UUT type to test, repeat paragraphs 7.3 through 7.8.  If all testing is completed.  Execute the “quit” command, F8 softkey.


7.10          This will bring up a window similar to that shown in Figure 5.  Execute the “exit” command, F8 softkey to log off the tester.



7.2              Remove the test fixture from the testhead and install the testhead covers. 

http://news.chivindo.com/286/operator-account-screens-and-options.html

Comments

Post a Comment

Popular posts from this blog

Basic PLC Ladder Programming Examples 23

Basic PLC Ladder Programming Examples 23 Basic PLC Ladder Programming Training Examples for Beginners.    Hi friends, here we are starting unique a series of Free Training on PLC Ladder Programming & tutorials. These PLC Ladder Programs are important to learn basics of Ladder programs. Example 7: Sequential control If we serially connect the normally closed contact of Y2 in example 5 to the circuit of Y1 as an AND condition for Y1 (as the diagram in the left hand side), the circuit can not only make Y1 as the condition for Y2, but also allow the stop of Y1 after Y2 is enabled. Therefore, we can make Y1 and Y2 execute exactly the sequential control Example 8: Oscillating circuit The ladder diagram above is a very simple one. When the program starts to scan the normally closed contact Y1, Y1 will be closed because coil Y1 is Off. When the program then scan to coil Y1 and make it On, the output will be 1. When the program scans to the normally closed contact Y1 again in the next scan
Post a Comment
Read more

Merakit pemancar mini FM

Merakit Pemancar mini FM Pemancar fm ini bekerja pada frekuensi 88- 108 MHz  dan memiliki jangkauan radius lebih dari 1 kilometer, tegangan yang digunakan sekitar  9 volt s/d 12 volt DC Pemancar ini menggunakan pcb produk ronica yang banyak dijual di toko elektronik dengan type Ronica SC-197                                                                                                                 Rangkaian ini sangat cocok untuk para pemula yang hobi elektronik. Karena rangkaiannya             sederhana dan komponennya mudah didapatkan di toko toko elektronik. Pemancar fm bisa dijadikan sebagai alat komunikasi geratis, memutar musik, untuk broadsact atau layak nya seperti siaran radio fm biasanya . pokoknya sangat mengasikan.   Pemancar fm ini terdiri dari 3 tingkat. Pada bagian osilator nya menggunakan transistor C9018, kemudian tingkat buffer 1 menggunakan 2 buah C930 yang dirangkai berpasangan, dan buffer terakhir rangkaian dari 4 buah C930. Ide merangkai transistor secara
Post a Comment
Read more

Takbiran Idul Adha 1440 H Jamaah Muda Masjid At Takrim Gapuk

Malam takbiran Idul Adha 1440 H ini terasa kurang afdol kalau tidak diadakan langsung acara takbiran bareng di masjid dan bentuk takbirannya pun bukan dari MP3 maupun CD yang diputar di CD Player lantas ditinggal pergi oleh Marbot masjid. Di Masjid At Takrim Gapuk Dasan Agung Mataram,  para jamaah muda yang tidak ikut pawai takbiran keliling akan berkumpul membentuk halaqoh/kumpulan sambil mengumandangkan bacaan takbiran saling sahut menyahut dengan membentuk pola suara yang uenak di dengar. Dan bila semakin malam maka akan semakin bertambah para jamaah yang ikut serta membaca takbiran hingga larut malam jam 03.00 pagi.  Kalau masalah bergadang hingga larut malam ini,  para jamaah muda ini sudah terbiasa karena mereka setiap malamnya selalu mertadarusan membaca Al Qur'an hingga jam 12.00 WITA. Alloohu akbar Alloohu Akbar Laaailaaha illallohu Alloohu Akbar Alloohu Akbar walillaahilham Gapuk Dasan Agung, malam ahad, 10082019  23.00 WITA  by: AlFuad Gapuki http://news.chivindo.com/211
Post a Comment
Read more