Skip to main content

Belajar Dasar SCADA

Post a Comment

REDUCING VALVE



Reducing Valves

Reducing valves automatically reduce supply pressure to a preselected pressure as long as the supply pressure is at least as high as the selected pressure. As illustrated in Figure 16, the principal parts of the reducing valve are the main valve; an upward-seating valve that has a piston on top of its valve stem, an upward-seating auxiliary (or controlling) valve, a controlling diaphragm, and an adjusting spring and screw.

Reducing valve operation is controlled by high pressure at the valve inlet and the adjusting screw on top of the valve assembly. The pressure entering the main valve assists the main valve spring in keeping the reducing valve closed by pushing upward on the main valve disk.However, some of the high pressure is bled to an auxiliary valve on top of the main valve. The auxiliary valve controls the admission of high pressure to the piston on top of the main valve.The piston has a larger surface area than the main valve disk, resulting in a net downward force to open the main valve. The auxiliary valve is controlled by a controlling diaphragm located
directly over the auxiliary valve.

The controlling diaphragm transmits a downward force that tends to open the auxiliary valve.The downward force is exerted by the adjusting spring, which is controlled by the adjusting screw. Reduced pressure from the main valve outlet is bled back to a chamber beneath the diaphragm to counteract the downward force of the adjusting spring. The position of the auxiliary valve, and ultimately the position of the main valve, is determined by the position of the diaphragm. The position of the diaphragm is determined by the strength of the opposing forces of the downward force of the adjusting spring versus the upward force of the outlet reduced pressure. Other reducing valves work on the same basic principle, but may use gas,pneumatic, or hydraulic controls in place of the adjusting spring and screw.

Non-variable reducing valves,replace the adjusting spring and screw with a pre-pressurized dome over the diaphragm. The valve stem is connected either directly or indirectly to the diaphragm. The valve spring below the diaphragm keeps the valve closed.As in the variable valve, reduced pressure is bled through an orifice to beneath the diaphragm to open the valve. Valve position is determined by the strength of the opposing forces of the downward force of the pre-pressurized dome versus the upward force of the outlet-reduced pressure.

Non-variable reducing valves eliminate the need for the intermediate auxiliary valve found in variable reducing valves by having the opposing forces react directly on the diaphragm.Therefore, non-variable reducing valves are more responsive to large pressure variations and areless susceptible to failure than are variable reducing valves.
http://news.chivindo.com/501/reducing-valve.html

Comments

Post a Comment

Popular posts from this blog

Basic PLC Ladder Programming Examples 23

Basic PLC Ladder Programming Examples 23 Basic PLC Ladder Programming Training Examples for Beginners.    Hi friends, here we are starting unique a series of Free Training on PLC Ladder Programming & tutorials. These PLC Ladder Programs are important to learn basics of Ladder programs. Example 7: Sequential control If we serially connect the normally closed contact of Y2 in example 5 to the circuit of Y1 as an AND condition for Y1 (as the diagram in the left hand side), the circuit can not only make Y1 as the condition for Y2, but also allow the stop of Y1 after Y2 is enabled. Therefore, we can make Y1 and Y2 execute exactly the sequential control Example 8: Oscillating circuit The ladder diagram above is a very simple one. When the program starts to scan the normally closed contact Y1, Y1 will be closed because coil Y1 is Off. When the program then scan to coil Y1 and make it On, the output will be 1. When the program scans to the normally closed contact Y1 again in the next scan
Post a Comment
Read more

Merakit pemancar mini FM

Merakit Pemancar mini FM Pemancar fm ini bekerja pada frekuensi 88- 108 MHz  dan memiliki jangkauan radius lebih dari 1 kilometer, tegangan yang digunakan sekitar  9 volt s/d 12 volt DC Pemancar ini menggunakan pcb produk ronica yang banyak dijual di toko elektronik dengan type Ronica SC-197                                                                                                                 Rangkaian ini sangat cocok untuk para pemula yang hobi elektronik. Karena rangkaiannya             sederhana dan komponennya mudah didapatkan di toko toko elektronik. Pemancar fm bisa dijadikan sebagai alat komunikasi geratis, memutar musik, untuk broadsact atau layak nya seperti siaran radio fm biasanya . pokoknya sangat mengasikan.   Pemancar fm ini terdiri dari 3 tingkat. Pada bagian osilator nya menggunakan transistor C9018, kemudian tingkat buffer 1 menggunakan 2 buah C930 yang dirangkai berpasangan, dan buffer terakhir rangkaian dari 4 buah C930. Ide merangkai transistor secara
Post a Comment
Read more

Takbiran Idul Adha 1440 H Jamaah Muda Masjid At Takrim Gapuk

Malam takbiran Idul Adha 1440 H ini terasa kurang afdol kalau tidak diadakan langsung acara takbiran bareng di masjid dan bentuk takbirannya pun bukan dari MP3 maupun CD yang diputar di CD Player lantas ditinggal pergi oleh Marbot masjid. Di Masjid At Takrim Gapuk Dasan Agung Mataram,  para jamaah muda yang tidak ikut pawai takbiran keliling akan berkumpul membentuk halaqoh/kumpulan sambil mengumandangkan bacaan takbiran saling sahut menyahut dengan membentuk pola suara yang uenak di dengar. Dan bila semakin malam maka akan semakin bertambah para jamaah yang ikut serta membaca takbiran hingga larut malam jam 03.00 pagi.  Kalau masalah bergadang hingga larut malam ini,  para jamaah muda ini sudah terbiasa karena mereka setiap malamnya selalu mertadarusan membaca Al Qur'an hingga jam 12.00 WITA. Alloohu akbar Alloohu Akbar Laaailaaha illallohu Alloohu Akbar Alloohu Akbar walillaahilham Gapuk Dasan Agung, malam ahad, 10082019  23.00 WITA  by: AlFuad Gapuki http://news.chivindo.com/211
Post a Comment
Read more