Skip to main content

Belajar Dasar SCADA

Post a Comment

Identification and Sorting of Defective Products using PLC Program



Identification and Sorting of Defective Products using PLC Program


Control Purpose:


 

  • Detecting the defective products (taller than normal dimension) on the conveyor belt by photoelectric sensor and pushing them into the recycle box at the 5th position. The pushing pole will be reset when the falling of defective product is detected. When errors occur, the disorder memory can be cleared and the system can be restarted by pressing RESET


Devices:

Device
Function
X0
Photoelectric sensor for detecting defective products
X4
Photoelectric sensor for monitoring the cam
X5
Photoelectric sensor for detecting the falling of defective products
X6
RESET
Y0
Electromagnetic valve pushing pole

PLC Program :




Program Description:
  •       Every time the cam rotates once, the product will be moved from one position to another position. X4 will be activated to execute SFTL instruction once. The content in M0~M4 will be shift to left for one bit and the state of X0 will be sent to M0.
  •   When X0 = ON (defective products detected), the value “1” will be sent to M0 and achieve the 5th position after 4 times of shift. In this case, M4 = ON and the electromagnetic valve Y0 will be ON to push the defective product into the recycle box.
  •  When the falling of the defective product is detected, X5 will be activated to execute [RST Y0] and [RST M4] instructions. Y0 and M4 will be reset. The electromagnetic valve will be OFF till next defective product is detected.
  •  When RESET is pressed, X6 will be activated to reset M0~M4, so as to ensure that the system restart the detecting process when the memory which records defective products is in disorder.





http://news.chivindo.com/808/identification-and-sorting-of-defective-products-using-plc-program.html

Comments

Post a Comment

Popular posts from this blog

Basic PLC Ladder Programming Examples 23

Basic PLC Ladder Programming Examples 23 Basic PLC Ladder Programming Training Examples for Beginners.    Hi friends, here we are starting unique a series of Free Training on PLC Ladder Programming & tutorials. These PLC Ladder Programs are important to learn basics of Ladder programs. Example 7: Sequential control If we serially connect the normally closed contact of Y2 in example 5 to the circuit of Y1 as an AND condition for Y1 (as the diagram in the left hand side), the circuit can not only make Y1 as the condition for Y2, but also allow the stop of Y1 after Y2 is enabled. Therefore, we can make Y1 and Y2 execute exactly the sequential control Example 8: Oscillating circuit The ladder diagram above is a very simple one. When the program starts to scan the normally closed contact Y1, Y1 will be closed because coil Y1 is Off. When the program then scan to coil Y1 and make it On, the output will be 1. When the program scans to the normally closed contact Y1 again in the next scan
Post a Comment
Read more

Merakit pemancar mini FM

Merakit Pemancar mini FM Pemancar fm ini bekerja pada frekuensi 88- 108 MHz  dan memiliki jangkauan radius lebih dari 1 kilometer, tegangan yang digunakan sekitar  9 volt s/d 12 volt DC Pemancar ini menggunakan pcb produk ronica yang banyak dijual di toko elektronik dengan type Ronica SC-197                                                                                                                 Rangkaian ini sangat cocok untuk para pemula yang hobi elektronik. Karena rangkaiannya             sederhana dan komponennya mudah didapatkan di toko toko elektronik. Pemancar fm bisa dijadikan sebagai alat komunikasi geratis, memutar musik, untuk broadsact atau layak nya seperti siaran radio fm biasanya . pokoknya sangat mengasikan.   Pemancar fm ini terdiri dari 3 tingkat. Pada bagian osilator nya menggunakan transistor C9018, kemudian tingkat buffer 1 menggunakan 2 buah C930 yang dirangkai berpasangan, dan buffer terakhir rangkaian dari 4 buah C930. Ide merangkai transistor secara
Post a Comment
Read more

Takbiran Idul Adha 1440 H Jamaah Muda Masjid At Takrim Gapuk

Malam takbiran Idul Adha 1440 H ini terasa kurang afdol kalau tidak diadakan langsung acara takbiran bareng di masjid dan bentuk takbirannya pun bukan dari MP3 maupun CD yang diputar di CD Player lantas ditinggal pergi oleh Marbot masjid. Di Masjid At Takrim Gapuk Dasan Agung Mataram,  para jamaah muda yang tidak ikut pawai takbiran keliling akan berkumpul membentuk halaqoh/kumpulan sambil mengumandangkan bacaan takbiran saling sahut menyahut dengan membentuk pola suara yang uenak di dengar. Dan bila semakin malam maka akan semakin bertambah para jamaah yang ikut serta membaca takbiran hingga larut malam jam 03.00 pagi.  Kalau masalah bergadang hingga larut malam ini,  para jamaah muda ini sudah terbiasa karena mereka setiap malamnya selalu mertadarusan membaca Al Qur'an hingga jam 12.00 WITA. Alloohu akbar Alloohu Akbar Laaailaaha illallohu Alloohu Akbar Alloohu Akbar walillaahilham Gapuk Dasan Agung, malam ahad, 10082019  23.00 WITA  by: AlFuad Gapuki http://news.chivindo.com/211
Post a Comment
Read more